RAILBLAZA Visibility Kit II
Code: PLU 7664
The RAILBLAZA Visibility Kit II is a must-have safety item in the kit of any kayak angler, or recreational paddler. In one convenient, value-for-money pack you get everything you need for your kayak or canoe to be seen on the water day and night.
Simply mount the StarPort HD with the supplied fastenings, lock in the 1 metre (3’) Extenda Pole 1000, clip on the orange flouro flag for daytime visibility, and lock the Illuminate i360 – All-round White Navigation Light into the port on top for safety and regulatory compliance at night.
Disassembly when you’re finished is quick and easy, and it will store just about anywhere.
The i360 light can also be fitted to other RAILBLAZA ports around the kayak, and the Extenda Pole 1000 can be used to display a dive or national flag, or combined with RAILBLAZA camera mounts as a camera pole.
Designed and made in New Zealand using high quality materials, and the latest LED technology
3 operation modes;
Full brightness navigation mode 2NM – up to 25hrs battery life
Low brightness work mode – up to 160 hrs battery life
Flashing emergency Mode – over 200hrs battery life
Waterproof to 1 metre
Floats with lens clear of water
Powered by 3 x AA batteries, not supplied
Meets USCG 2NM 33 CFR 183.810 & ABYC A-16
Independently tested by Imanna Labs Inc, Florida
Supplied with StarPort HD, but will fit any other RAILBLAZA mounting port, ordered separately.
Flouro safety flag dimensions – 450mm (18 inches) x 200mm (8 inches)
RAILBLAZA 3 piece Extenda Pole can be configured as;
1 section height 380mm (15”)
2 sections height 680mm (27”)
3 sections height 980mm (38.5”)
Increase your kayak's visibility on the water with this 1200mm flexiwhip pole.
Designed to fit into the Starport Base Mount (which we fit as standard onto the rear all of our kayaks)
300 x 150 mm pennant included.
Easily removed for transporting.
Anchor Running Rig by New Zealand Kayaker
Being able to pull an anchor from the front of the boat is critical to safety and stability. The anchor running kit is essential equipment that allows the anchor to be attached from the seat then pulled around to the front
Code: PLU 1092
Adjustable and easy to fit footrest pair.
Great for when you need that extra bit of traction/purchase!
Popular with the shorter adults that have difficulty reaching the standard kayak footwells.
Comes as a pair
(Please order the six 10 gauge screws required, separately)
One of the reasons our footrests and tip toes are a bit more expensive than some of the others available is that we use the best grade of Du Pont nylon available and this does have a premium attached.
We have experimented with other grades but none of them have stood up to the testing rig which stresses the part to 3g. As the footrests are considered a safety item we consider reliability is very important.
Thigh Braces by Viking
Sold as a pair, these sit on top kayak thigh braces will give you greater control over your kayak especially in the surf.
Thigh braces replicate the feeling of an enclosed cockpit giving greater control and ability to rail your kayak,
They are also useful aids for assisting you in tracking when you do not have a rudder.
Fits to all Sit on Top kayaks by simply threading through saddles or grab/deck lines, or by using a Thigh Brace Fit Kit.
Viking Angler Rudder System (short blade design) DIY kit will fit any of the Viking Profish kayaks.
Code: PLU 5013
Designed specifically for kayak anglers and paddlers who want a hassle free rudder system whether they’re launching from surf beaches, exploring the kelp beds, or paddling wide of the coast.
The short blade design doesn’t need an up-haul and is always working, even when the water is almost too shallow to paddle. In deeper water the short design ensures the rudder rests in the kayak’s wake without adding any significant drag – the ultimate in efficiency.
Now with 'Toe Tab' foot controls for superior control.
The 'Angler' blade works fantastic, plus there is no requirement for an up haul - super convenient.
A rudder system will make your kayak much easier to manage in windy conditions.
FOR FACTORY FITTING THE COST IS $350.00
Viking Replacement Rudder Blade - Mk3
Code: PLU 3183
Replacement Rudder Blade for the latest Viking Kayaks rudder system using the black synthetic KS headstock.
This blade shape fits the black synthetic Mark 3 rudder headstocks only.
This design uses the latest material with a higher rubber content so it's more resistant to breakage.
Important - this blade design is not compatible with the older rudder systems. Please ensure you order the correct blade for your kayak.
Code: PLU 1072
For when you have lost the bung out of the rear of your Viking kayak
To fit to a kayak you will need to drill a 25mm hole
If you need a replacement bung only, simply separate these two parts and screw the Male fitting into the base that you already have.
*the diameter of the thread is 19mm
Screws not included but can be ordered seperately if required (10g x 5/8)
RailBlaza Mobile Device Holder
Extra safe mounting for your mobile devices.
The RAILBLAZA Mobile Device Holder, or “Mobi” for short, is ready to look after your phone, GPS, VHF, EPIRB or other mobile device.
Our unique design brings a new level of versatility to the device holder market, once you have your Mobi you can attach it to any vessel or vehicle on water or land – basically any place you can install a RAILBLAZA StarPort, RIBPort or RailMount.
The spring loaded arms are sufficient for most applications, with neoprene rubber pads to give high gripping power. For extra peace of mind the adjustable, UV stabilised, Eurethane rubber retaining strap ensures your device goes nowhere, even in the most rugged environment.
Railblaza Camera Boom 600
The RAILBLAZA Pro Series Boom 600 is the perfect way to hold your camera and capture the action.
The camera boom 600 is really useful for overhead shots, and many other great angles to really get some unique footage.
Product features include;
5 adjustment axes, the 5th axis is for "horizon correction", so if the Boom is mounted on a sloping surface you can still get the horizon level with a quick tweak of this 5th joint
All friction joints are factory set, no need to tighten any joints.
The top platform is fully removable, allowing you to use it as a low profile camera mount, and you can retask the pole to carry a light or other accessory, a new level of versatility!
Satin black anodised finish, this removes any reflection, and makes the boom fade into the background.
Compatible with any RAILBLAZA StarPort, SidePort, RIBPort or RailMount (mounts not included)
RailBlaza Rotating Platform
For simplicity of mounting, you can't go past the RAILBLAZA Rotating Platforms. They are the ideal mount if you need the ability to easily remove your sounder or navigational aid. Once locked into a StarPort the platform can be turned a full 360 degrees.
Made from a combination of high quality UV proof engineering plastics, UV proof HDPE, and stainless steel screws it allows mounting of brackets with any combination of holes, if using smaller self tapping screws you can screw directly in without the need to drill pilot holes.
The Rotating Platform can be used as a flat surface to make many items StarPort compatible, meaning these items can all be plugged in and locked in place on your inflatable, kayak, sailboat or any other place that will take a StarPort. Once you have finished using the platform it can be removed and the StarPort can be retasked for another application.
RailBlaza Adjustable Platform
These can be used to fit fish finders to kayaks like the Viking Espri or Viking 2+1.
You will need to also purchase a Starport and base for it to click into if your kayak does not have one fitted.
If you want to fit other Rail Blaza accessories then the TracPort Dash may be just what you are after as you can then fit a fish finder, GPS, VHF, rod holder to the same track.
RailBlaza Extenda Pole 1000
The TelePole adds another dimension of versatility to the RAILBLAZA system, it compresses to 630mm and expands to 1060mm with a male StarPort adaptor at one end and a female StarPort at the top end. Fly a flag, attach a NAVISAFE 360 LED navi light, attach a 3 axis camera mount or you can even add an adjustable extender with G-Hold. Fits into any StarPort, SidePort , RailMount or RIBPort.
NOTE: Due to the wide range of applications for the RAILBLAZA TelePole 1000, we cannot state a maximum safe weight it will support. While we recommend no more than 450grams (1lb), there are conditions in which this weight will be too much.
RAILBLAZA recommend gear is tethered to the vessel at all times, and we cannot take responsibility for any gear lost